Netapp Snapmirror Setup Guide

Netapp Snapmirror Setup Guide

Snapmirror is an licensed utility in Netapp to do data transfer across filers. Snapmirror works at Volume level or Qtree level. Snapmirror is mainly used for disaster recovery and replication.

Snapmirrror needs a source and destination filer. (When source and destination are the same filer, the snapmirror happens on local filer itself. This is when you have to replicate volumes inside a filer. If you need DR capabilities of a volume inside a filer, you have to try syncmirror ).

Synchronous SnapMirror is a SnapMirror feature in which the data on one system is replicated on another system at, or near, the same time it is written to the first system. Synchronous SnapMirror synchronously replicates data between single or clustered storage systems situated at remote sites using either an IP or a Fibre Channel connection. Before Data ONTAP saves data to disk, it collects written data in NVRAM. Then, at a point in time called a consistency point, it sends the data to disk.

When the Synchronous SnapMirror feature is enabled, the source system forwards data to the destination system as it is written in NVRAM. Then, at the consistency point, the source system sends its data to disk and tells the destination system to also send its data to disk.

This guides you quickly through the Snapmirror setup and commands.

1) Enable Snapmirror on source and destination filer

source-filer> options snapmirror.enable
snapmirror.enable on
source-filer>
source-filer> options snapmirror.access
snapmirror.access legacy
source-filer>

2) Snapmirror Access

Make sure destination filer has snapmirror access to the source filer. The snapmirror filer's name or IP address should be in /etc/snapmirror.allow. Use wrfile to add entries to /etc/snapmirror.allow.

source-filer> rdfile /etc/snapmirror.allow
destination-filer
destination-filer2
source-filer>

3) Initializing a Snapmirror relation

Volume snapmirror : Create a destination volume on destination netapp filer, of same size as source volume or greater size. For volume snapmirror, the destination volume should be in restricted mode. For example, let us consider we are snapmirroring a 100G volume - we create the destination volume and make it restricted.

destination-filer> vol create demo_destination aggr01 100G
destination-filer> vol restrict demo_destination

Volume SnapMirror creates a Snapshot copy before performing the initial transfer. This copy is referred to as the baseline Snapshot copy. After performing an initial transfer of all data in the volume, VSM (Volume SnapMirror) sends to the destination only the blocks that have changed since the last successful replication. When SnapMirror performs an update transfer, it creates another new Snapshot copy and compares the changed blocks. These changed blocks are sent as part of the update transfer.

Snapmirror is always destination filer driven. So the snapmirror initialize has to be done on destination filer. The below command starts the baseline transfer.

destination-filer> snapmirror initialize -S source-filer:demo_source destination-filer:demo_destination
Transfer started.
Monitor progress with 'snapmirror status' or the snapmirror log.
destination-filer>

Qtree Snapmirror : For qtree snapmirror, you should not create the destination qtree. The snapmirror command automatically creates the destination qtree. So just volume creation of required size is good enough.

Qtree SnapMirror determines changed data by first looking through the inode file for inodes that have changed and changed inodes of the interesting qtree for changed data blocks. The SnapMirror software then transfers only the new or changed data blocks from this Snapshot copy that is associated with the designated qtree. On the destination volume, a new Snapshot copy is then created that contains a complete point-in-time copy of the entire destination volume, but that is associated specifically with the particular qtree that has been replicated.

destination-filer> snapmirror initialize -S source-filer:/vol/demo1/qtree destination-filer:/vol/demo1/qtree
Transfer started.
Monitor progress with 'snapmirror status' or the snapmirror log.

4) Monitoring the status : Snapmirror data transfer status can be monitored either from source or destination filer. Use "snapmirror status" to check the status.

destination-filer> snapmirror status
Snapmirror is on.
Source Destination State Lag Status
source-filer:demo_source destination-filer:demo_destination Uninitialized - Transferring (1690 MB done)
source-filer:/vol/demo1/qtree destination-filer:/vol/demo1/qtree Uninitialized - Transferring (32 MB done)
destination-filer>

5) Snapmirror schedule : This is the schedule used by the destination filer for updating the mirror. It informs the SnapMirror scheduler when transfers will be initiated. The schedule field can either contain the word sync to specify synchronous mirroring or a cron-style specification of when to update the mirror. The cronstyle schedule contains four space-separated fields.

If you want to sync the data on a scheduled frequency, you can set that in destination filer's /etc/snapmirror.conf . The time settings are similar to Unix cron. You can set a synchronous snapmirror schedule in /etc/snapmirror.conf by adding “sync” instead of the cron style frequency.

destination-filer> rdfile /etc/snapmirror.conf
source-filer:demo_source destination-filer:demo_destination - 0 * * * # This syncs every hour
source-filer:/vol/demo1/qtree destination-filer:/vol/demo1/qtree - 0 21 * * # This syncs every 9:00 pm
destination-filer>

6) Other Snapmirror commands

• To break snapmirror relation - do snapmirror quiesce and snapmirror break.
• To update snapmirror data - do snapmirror update
• To resync a broken relation - do snapmirror resync.
• To abort a relation - do snapmirror abort

Snapmirror do provide multipath support. More than one physical path between a source and a destination system might be desired for a mirror relationship. Multipath support allows SnapMirror traffic to be load balanced between these paths and provides for failover in the event of a network outage.

To read how to tune the performance & speed of the netapp snapmirror or snapvault replication transfers and adjust the transfer bandwidth , go to Tuning Snapmirror & Snapvault replication data transfer speed

source: http://unixfoo.blogspot.com/2009/01/netapp-snapmirror-setup-guide.html